本文針對內部模型控制（Internal Model Control, IMC）應用於低阻尼受控體（lightly damped plants）會有超越量或震盪的問題，進行控制器初始值補償（Initial Value Compensation, IVC）之設計。內部模型控制器具有容易設計的優點，透過初始值補償之設計可以明顯地降低超越量或震盪現象的發生，藉此能夠提升控制系統的暫態性能。
本文的實驗平台是以無刷伺服馬達結合導螺桿而成的線性平台，進行線性運動定位控制的實驗。訊號處理部分採用美國德州儀器公司（Texas Instruments, TI）生產之TMS320C6713 DSP搭配FPGA自製擴充子板與Xilinx可程式閘陣列（FPGA）結合而成之控制器硬體核心，以C語言與硬體描述語言（VHDL）作為控制器設計之發展工具。經由實驗結果可得知，加入初始值補償之控制器，能有效的改善傳統控制器的缺點，改善系統的暫態響應。

This thesis presents a solution to the overshoot and oscillation problems when the Internal Model Control (IMC) is applied to the lightly damped plants. By using Initial Value Compensation (IVC), the plant’s output overshoot and oscillation can be significantly reduced, thus, improving the performance of the control system.
The experimental system consists of a brushless servo motor and a ball screw for experimental verification. The C language and VHSIC Hardware Description Language (VHDL) are tools for developing a control system. The experimental results show that the IVC can effectively reduce the output overshoot and oscillation caused by the conventional IMC.

[1] M. Iwasaki, N. Hirose, M. Kawafuku, and H. Hirai, “Residual Vibration Suppression Using Initial Value Compensation for Repetitive Positioning,” in Proc. of 8th International Workshop on Advanced Motion Control, pp. 571-576, 2004.
[2] N. Hirose, K. S. Safety, H. Kajima, and M. Yamaoka, “Mode Switching Control for a Personal Mobility Robot based on Initial Value Compensation,” Proc. of Annual Conference on IEEE Industrial Electronics Society, pp. 1914-1919, 2010.
[3] Y. S. Lu and C. M. Cheng, “Design of a Non-Overshooting PID Controller with an Integral Sliding Perturbation Observer for Motor Positioning Systems,” JSME International Journal Series C, vol. 48, no. 1, pp. 103-110, 2005.
[4] T. Yamaguchi, H. Numasato, and H. Hirai, “A Mode-Switching Control for Motion Control and Its Application to Disk Drives: Design of Optimal Mode-Switching Conditions,” IEEE/ASME Trans. Mechatronics, vol. 3, no. 3, pp. 202-209, 1998.
[5] 劉聖濠，積分控制之初始值補償策略實作，碩士論文，國立雲林科技大學機械工程系，雲林、台灣，2008。
[6] N. S. Nise, Control Systems Engineering, Wiley, New York, 2004.
[7] T. Yamaguchi, K. Shishida, H. Hirai, K. Tsuneta, and M. Sato, “Improvement of Servo Robustness for Digital Sector Servo System,” IEEE Trans. Magn., vol. 28, pp. 2910-2912, Sept. 1992.
[8] T. Yamaguchi, Y. Soyama, H. Hosokawa, K. Tsuneta, and H. Hirai, “Improvement of Settling Response of Disk Drive Head Positioning Servo Using Mode Switching Control with Initial Value Compensation,” IEEE Trans. Magn., vol. 32, no. 3, pp. 1767-1772, May 1996.
[9] T. Yamaguchi, K. Shishida, S. Tohyama, Y. Soyama, H. Hosokawa, H. Ohsawa, H. Numasato, T. Arai, K. Tsuneta, and H. Hirai, “A Mode Switching Controller with Initial Value Compensation for Hard Disk Drive Servo Control,” Contr. Eng. Practice, vol. 5, no. 11, pp. 1525-1532, 1997.