溝槽管廣泛地應用於電子產業的散熱元件中，一般而言，其製作皆需透過模具抽拉成形，因此在製作更小尺度的溝槽管時，往往會產生限制。本研究試圖提出另一種加工方法來改善此成形限制，意即利用脈衝式雷射輔助氣壓無模成形，並找出製程參數對不銹鋼薄管溝槽成形之影響。本研究的成形方法是在大氣的環境下，使用一般空氣為工作加壓氣體，再利用脈衝式雷射為加熱源，在不銹鋼薄管內側成形溝槽。接著用光學顯微鏡觀察成形後金相組織，以微硬度試驗測量硬度變化，最後再以掃描式電子顯微鏡搭配能量散佈光譜儀進行觀察及分析。研究結果顯示，利用脈衝式雷射輔助氣壓無模成形可成功地在任何位置製作溝槽，在雷射輸出功率10W及氣體壓力0.1kg/cm2下，可製作出平均槽寬382.5um、平均槽深208.5um的溝槽。此結果指出，即便成品需達到微米尺度，亦能藉由無模成形的方式獲得。

Nowadays, groove tubes are widely used in the electronic cooling module. It is usually drawn which term refers to molding. However, there are limitations while producing the smaller ones. Therefore, this study emphasis on the parameters of dieless forming which affects the shaping of groove on stainless steel that generated by pulsed laser assisted air pressure. In this study, the performance is presented on the basis of standard atmospheric conditions. To begin with, the stainless steel tube is heated by pulsed laser with ambient air surrounded and it soon forms the target groove. Then, groove samples are sliced to be observed using OM and the Vickers hardness test determines these samples’ hardness values. Finally, the samples are observed and analyzed with the aids of a SEM and an EDS. The results demonstrate that the groove can be done utilizing dieless forming with pulsed laser assisted air pressure. It is notably that the average width of groove is 382.5um and the average depth is 208.5um at 10 watt power and 0.1kg/cm2 gas pressure. In conclusion, groove in micro scale can be obtained effectively by dieless forming for industrial applications.

[1] B. H. Amstead， Pillip F. Ostwald，Myron L. Begeman，Manufacturing Processes，8th Edition，Wiley，University of Michigan，1987
[2] 杜成偉，楊愷祥，羅稚駿，簡國祥，”薄型熱管與均熱板之發展趨勢及近況”，工業材料，328期，62頁，2014
[3] 周長彬，蘇程裕，蔡丕樁，郭央諶，銲接學，全華圖書股份有限公司，台北，2012
[4] Cverna，Fran (EDT)，Conti，Patricia (EDT)，Worldwide Guide to Equivalent Irons and Steels，4th Ed.，Asm Intl，USA，2000
[5] 鄭皓文，"脈衝式雷射製作氮作鋁層之研究"，國立臺灣師範大學工業教育學系，碩士論文，2011
[6] 丁勝懋，光電工程。台北：中國電機工程學會，1999
[7] 黃俊榮，AZ型鎂合金微銲接之最適參數研究，國立台灣師範大學工業教育學系，碩士論文，2005
[8] F. Fariaut，C. Boulmer-Leborgne，"Light alloy upgrading by surface laser treatment"，Proc. SPIE 4760，125，2002
[9] A. Punkari，D. C. Weckman，H. W. Kerr，"Effects of magnesium content on dual beam Nd:YAG laser welding of Al-Mg alloys"，Science and Technology of Welding and Jointing，Vol.8， No.4， pp.269-281，2003
[10] 蔡偉崙，"脈衝式Nd:YAG雷射銲接5052鋁合金薄板製程參數之研究"，中國機械工程學會第二十屆全國學術研討會論文集，第D冊 製造與材料 上集，頁127-133，2003
[11] Ramasamy，Sivakumar.，"CO2 and Nd:YAG laser beam Nd:YAG laser beam welding of 6111-T4 and 5754-O aluminum alloys for automotive applications. "，New York: UMI Dissertation Information Service，pp.18-31，1997.
[12] 蔡偉崙，脈衝式Nd:YAG雷射封裝3003鋁合金方型鋰電池殼體之機械性質與熱傳分析，國立台灣師範大學工業教育學系，碩士論文，2004
[13] 沈志宏，成型加工對於熱管性能影響之探討，大同大學，碩士論文，2007
[14] 杜成偉，楊愷祥，羅稚駿，簡國祥，”薄型熱管與均熱板之發展趨勢及近況”，工業材料，328期，62頁，2014
[15] L.V. Grasty ，"Shot Peen Forming"，Cambridge University，Ph.D.，1992
[16] 祝林，"金屬板料三維曲面無模多點成形技術及其應用"，四川職業技術學院學報，23卷，3期，2013
[17] 張凌雲，張飛，"高壓水射流板材漸進成形工藝的進展"，鑄造技術，31卷，5期，P649 - 652，2010
[18] 杜如虛，何凱，李赳華，羅遠新，”金屬板材無模成形技術發展綜述”，先進技術研究通報，第二期，2010
[19] 尚建勤，"送進速度對拋丸成形影響的試驗研究"，塑性工程學報，第7卷，第2期，2000
[20] FerroECOBlast，http://ferroecoblast.com/products/shot_peening_peen_forming/13/peen_forming/
[21] M.Z. Li，Z.Y. Cai，Z.Sui，Q.G.Yan，"Multi-point forrning technology for sheet rnetal"，Journal of Materials Processing Technology，Issues 1–3，Volume 129，Pages 333–338
[22] Bostjan Jurisevic, Karl Kuzman, Mihael Junkar，"Water jetting technology: an alternative in incremental sheet metal forming"，The International Journal of Advanced Manufacturing Technology，Issues 1–2，Volume 31，pp 18-23，2006
[23] Jong-Jin Park，Yung-Ho Kim，"Fundamental studies on the incremental sheet metal forming technique"，Journal of Materials Processing Technology，Issues 1–3，Volume 140，Pages 447–453，2003
[24] Namba Y.，Laser forming in space, International Conference on Lasers’85， editors: Wang C. P.，pp.403-407，1986
[25] Scully K，"Laser line heating"，Journal of Ship Production，3,237-246，1987
[26] Arnet H. and Vollertsen F.，"Extending laser bending for the generation of convex shapes"，J. Eng. Manuf， Vol. 209，pp.433-442，1995.
[27] D.P. Shidid，M.HoseinpourGollo，M.Brandt，M.Mahdavian，"Study of effect of process parameters on titanium sheet metal bending usingNd: YAG laser"，Optics & Laser Technology，47，pp.242-247，2013
[28] Xiao Wang，Daozhong Du，Hu Zhang，Zongbao Shen，Huixia Liu，Jianzhong Zhou，Hui Liu，Yang Hu，Chunxing Gu，"Investigation of microscale laser dynamic flexible forming process - simulation and experiments"，International Journal of MachineTools & Manufacture，67 pp.8-17，2013
[29] 賴耿陽，管材加工二次成形，復漢出版社，台北，1993
[30] 周宗易，"液壓成形(Hydro-forming)於閥製品之應用"，中國機械工程學會第二十一屆全國學術研討會論文集，2004
[31] 邱先拿，"管材液壓成形技術之應用狀況與發展動向"機械月刊，Vol. 26， No. 10，p. 369，2000
[32] M. Kleiner，A. Gartzke，R. Kolleck，E.v. Finckenstein，"Experimental and Finite Element Analysis of Capabilities and Limits of a Combined Pneumatic and Mechanical Deep-Drawing Process"，CIRP Annals - Manufacturing Technology，Issue 1，Volume 46，Pages 201–204，1997
[33] Chin-Tarn Kwan，"利用高壓空氣作氣壓板金成形新製程開發之研究"，2009
[34] Hans Kurt Tönshoff，J. Bunte, O. Meier，L. Engelbrecht，"Deformation Behaviour of Sheet Metals in Laser Assisted Hydroforming Processes"，Advanced Materials Research，Vol.6-8，pp361-368，2005
[35] Metal Technology Co. Ltd.，http://www.kinzoku.co.jp/english/index.html?lid=0
[36] L. Vadillo，M.T. Santos，M.A. Gutierrez，I. Pérez，B.González and V. Uthaisangsuk，"Simulation And Experimental Results Of The Hot Metal Gas Forming Technology For High Strength Steel And Stainless Steel Tubes Forming"，Proceedings of the 9th International Conference on Numerical Methods in Industrial Forming Processes，2007
[37] HE Zhu-bin，TENG Bu-gang，CHE Chang-yong，WANG Zhi-biao，ZHENG Kai-lun，YUAN Shi-jian，"Mechanical properties and formability of TA2 extruded tube for hot metal gas forming at elevated temperature"，Transactions of Nonferrous Metals Society of China，Volume 22，Pages s479–s484，2012
[38] HE Zhu-bin，FAN Xiao-bo，SHAO Fei，ZHENG Kai-lun，WANG Zhi-biao，YUAN Shi-jian，"Formability and microstructure of AA6061 Al alloy tube for hot metal gas forming at elevated temperature"，Transactions of Nonferrous Metals Society of China，Volume 22，Pages s364–s369，2012